top of page

Technical Data Sheet

MILES 8659-Gel

Non-Methylene Chloride Stripper

Room Temperature Aluminum Wheel Stripper Gel - for Brush on Applications
Description:
Directions:
Warning:
First Aid:
Hazard Class:
MILES 8659 is a non-methylene chloride, thickened gel, aluminum wheel stripper formulated to remove all types of cured coatings from aluminum, brass, stainless and steel. MILES 8659 can be used to remove Automotive OEM coatings from Aluminum Alloy Wheels overnight. Non-flammable, acid accelerated alternative to hazardous methylene chloride strippers. Not safe for use on magnesium, may be used on Galvanized and certain types of Zinc substrates at room temperature. Tire Rubber must be removed from wheel/rim prior to using stripper. Stripper will attack Wheel rubber, Latex, Acrylics, Vinyl, Fiberglass, PVC and ABS plastics.
 
Apply generously with natural bristle brush, solvent safe roller or airless spray to surfaces to be stripped, let set for 2 to 4 hours to remove powder coating, for removal of OEM Aluminum wheel coatings, let set covered with polypropylene plastic over night. Once coating is softened and lifted, remove with plastic scraper, disposable rags, shot blast media or rinse with pressure washer 1500-4500 psi. Contain waste and neutralize by sprinkling with Bicarbonate of Soda, then dispose of as non-hazardous solid, per your local regulations. 
 
May be harmful if swallowed. May cause skin and eye irritation. Eye protection and chemical resistant  Heavy Nitrile safety gloves are recommended when handling paint stripping chemical solutions.
 
In case of eye or skin contact flush with large amounts of water for 15 minutes. If irritation persists, see physician. In case of ingestion, do not induce vomiting; drink large quantities of water to dilute product. Seek medical attention at once.
 
 
 UN3265, Corrosive Liquid, Acidic, organic, N.O.S., (Contains Glycolic Acid), 8, PGII
 
 
 
 
 
 
 

Technical Data Sheet

MILES 8660

Non-Methylene Chloride Stripper

Room Temperature  or low Temperature Aluminum Wheel Stripping Solution
Liquid for Immersion Applications
Description:
Directions:
Warning:
First Aid:
Hazard Class:
MILES 8660 is a Room Temperature, Non-flammable, acid accelerated alternative to hazardous Methylene chloride strippers, concentrated-liquid, aluminum wheel stripping solution formulated to remove all types of cured coatings from aluminum, brass, stainless and steel. May be heated to130F.-150F. to accelerate stripping time. MILES 8660 can be used heated to strip all types of Powder Coatings, OEM coatings from Aluminum Alloy Wheels, E-coating, Military CARC and difficult to remove PVD Primers. Not safe for use for zinc or magnesium substrates. Tire Rubber must be removed from wheel/rim prior to using stripper. Stripper will attack Wheel rubber, Latex, Acrylics,Vinyl, Fiberglass, PVC and ABS plastics.
 
Utilize a stainless steel or polypropylene immersion tank with lid. Ready to use at 100% concentration for room temperature stripping or can be diluted with up to 50% water when heated to 130F.-150F. Strip time  heated is 15 minutes to 1.5 hours and at room temperature strip time is   2-hours to overnight, depending on the type coating and coating film build. Agitation with a stainless-steel mixer will accelerate strip time. Never use direct air agitation into solution, as it will deplete solution life.
 
 
May be harmful if swallowed. May cause skin and eye irritation. Eye protection and chemical resistant  Heavy Nitrile safety gloves are recommended when handling paint stripping chemicals. Do not use thin disposable safety gloves, rinse safety gloves with water after each use.
 
In case of eye or skin contact flush with large amounts of water for 15 minutes. If irritation persists, see physician. In case of ingestion, do not induce vomiting; drink large quantities of water to dilute product. Seek medical attention at once.
 
UN3265, Corrosive Liquid, Acidic, organic, N.O.S., (Contains Glycolic Acid), 8, PGII
 
 
 
 
 
 
bottom of page